For best results, make sure your ingredients are uniform in size before adding them to the food processor bowl. Follow the guidelines below for best results:

Trim ingredients so they are in 10-12cm pieces or slightly over the height of the feed chute. DO NOT cut ingredients smaller than the size of the feed chute.

Cut both ends off ingredients to create flat surfaces. Trim tapered ingredients like carrots to make them more symmetrical.

Larger ingredients, such as potatoes, may need to be cut in half lengthwise.

The bowl can hold up to 9 cups when filled to the max fill line.

There are 4 Auto-iQ functions:
Chop
Puree (not available on all models)
Dough
Disc

There are 3 different manual functions:
Low
High
Pulse

You can create any of your favorite doughs, from pie and pizza dough to your favourite cookie doughs.

1. Place motor base on a clean, dry, level surface such as a countertop or table, then plug in the unit.
2. Lower the Precision Processor® Bowl on the motor base and rotate clockwise until it clicks into place.
3. Exercising care, grasp the Chopping Blade Assembly by the top of the shaft and place it onto the drive gear inside the bowl. Note that the Chopping Blade Assembly will fit loosely on the drive gear.
4. Add ingredients to the bowl, making sure not to exceed the Max Fill line.
5. Place the feed chute lid on the bowl and turn clockwise until you hear a click, indicating the lid is locked in place. You are now ready to select a manual or Auto-iQ® program to start processing.

1. Place motor base on a clean, dry, level surface such as a countertop or table, then plug in the unit.
2. Lower the Precision Processor® Bowl on the motor base and rotate clockwise until it clicks into place.
3. Place the disc spindle onto the drive gear inside the bowl. Then use the finger holes to grasp the disc and place it over the spindle, with the side you would like to use facing up. NOTE: The Slicing/Shredding Disc is reversbile.
4. Place the feed chute lid on the bowl and turn clockwise until you hear a click, indicating the lid is locked in place.
5. Press the Power button to turn the unit on, then select DISC or LOW. Add the prepped ingredients you want to slice or shred through the feed chute on the lid. Use the food pusher to help guide the ingredients through the feed chute.

Using the finger holes, carefully lift the disc out of the bowl. Then grasp the spindle by the top of the shaft and lift it out of the bowl.

To remove the bowl from the motor base, turn the bowl counterclockwise and then lift it up.

If you selected an Auto-iQ® program, there will be a unique processing and pausing pattern that does the work for you. Once an Auto-iQ program is selected, it will start immediately and automatically stop when processing is complete. To stop processing before the end of a program, press the currently active button again.

The Low and High functions will run continuously for 60 seconds.

Lower the Precision Processor® Bowl onto the motor base and rotate clockwise until it clicks into place.

Wash bowl, lid, disc(s), and blade assemblies in warm, soapy water. When washing the blade assemblies, use a dishwashing utensil with a handle to avoid direct hand contact with blades. Handle blade assemblies with care to avoid contact with sharp edges. Rinse and air-dry thoroughly.

All attachments are dishwasher safe. It is recommended that the bowl, lid, disc(s), and blade assemblies be placed on the top rack of the dishwasher ONLY. Ensure the blade assembly is removed from the bowl before placing in the dishwasher. Exercise care when handling blade assemblies.

You should stop the program and use a spatula to clean the blades. NEVER insert a utensil in the unit while it is running.

For best results when chopping, cut ingredients in a uniform size and don’t overfill the bowl.

For best results when using the Reversible Slicing/Shredding Disc or Crinkle Cut Disc, trim ingredients to a uniform size so they fit better through the feed chute. Do not cut ingredients smaller than the feed chute height.

Make sure the counter and feet of the unit are clean and dry.
Motor base won’t stick to counter or tabletop.
Make sure surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces.
Suction feet will not stick to some surfaces such as wood, tile, and non-polished finishes.
DO NOT attempt to use unit when the motor base is stuck to a surface that is not secure (cutting board, platter, plates, etc.).